A&D AD-8922A Bedienerhandbuch

AD-4212C-300 AD-4212C-600 AD-4212C-3000 AD-4212C-6000 AD-4212C-301 AD-4212C-3100 Production Weighing Unit INSTRUCTION MANUAL 1WMPD4001992B

8Rear of theweighing unitRS-232C cableD-sub 9-pinArrow markface up2.2. Installing the Balance Install the balance as follows: 1. Refer to “3. PRECAU

9MASS OF THE LOCALLY FABRICATED WEIGHING PAN Design the weighing pan so that the mass falls within the ranges shown in the table below: Model Statu

103. PRECAUTIONS To get the optimum performance from the balance and acquire accurate weighing data, note the following: 3.1. Before Use  Install

113.2. When Building Into a System The AD-4212C is a precision balance. When it is built into a system, errors such as unstable weight values may o

12 Errors due to a static charge and measures to take When the ambient humidity is less than 45% RH, insulators such as plastic or glass are prone

13 Errors due to air flow and measures to take Where the influence of ambient air flow is great such as: close to an air conditioner, door or pass

143.3. During Use  To minimize the affect by electrical noises, earth ground the weighing unit and the display unit (option).  Do not drop things

154. OPERATION OF WinCT-AD4212C The software has the following functions: - Set the weighing speed - Set the minimum display value - Calibration

164.1. Changing the Weighing Speed Using WinCT-AD4212C The weighing speed can be selected from the following three rates to minimize the influence

17 Calibration procedure This function calibrates the balance using the calibration weight. (Display example: AD-4212C-300) Operation 1. Plug in t

© 2011 A&D Company, Limited. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, or translated into

184.3. Changing the Baud Rate Using WinCT-AD4212C Operation 1. Click the [Settings] tab. 2. Select the baud rate to be used and click the Set

195. SMART RANGE FUNCTION The AD-4212C-301/3100 are equipped with two ranges. The precision range has a higher resolution. The standard range has a n

206. COMMUNICATION SPECIFICATIONS The AD-4212C series can communicate interactively using RS-232C. The AD-4212C series can continuously transmit th

212. Pin position Pin position of the RS-232C cable (D-Sub 9-pin side, female) Pin No. Signal name Direction Description 1 (Vs) - Internally u

224. Command The balance can be controlled by the following commands. When transmitting, add the terminator <CR><LF> to each command. Co

23 CAL command example (PC, PLC)External devices Time Weighing unit 　CAL commandDisplays

24 SMP command example R command example when the precision range is used SMP commandSMPCRLFST,+0000.012 gS

257. MAINTENANCE  Do not disassemble the balance. Contact the local A&D dealer if the balance needs service or repair.  Use the original pac

268. TROUBLESHOOTING 8.1. Checking the Balance Performance and Environment The balance is a precision instrument. When the operating environment or

27 Sample and container  Has the sample absorbed or lost moisture?  Has the temperature of the sample, and the container if used, been allowed to

1CONTENTS 1. INTRODUCTION...2

289. SPECIFICATIONS AD-4212C-300 AD-4212C-600 AD-4212C-301 Weighing capacity 320 g 620 g 320 g / 51 g*1 Maximum display 320.084 g 620.084 g

29 AD-4212C-3000 AD-4212C-6000AD-4212C-3100 Weighing capacity 3200 g 6200 g 3200 g / 510 g*1 Maximum display 3200.84 g 6200.84 g 3200.84 g / 51

3010. EXTERNAL DIMENSIONS - AD-4212C-300 / 600 / 3000 / 6000 / 301 / 3100 Unit: mm 9848.83018.846505091.9 1

3111. OPTIONS AX-KO3590-200 RS-232C cable 2 m AX-KO3590-500 RS-232C cable 5 m AX-KO3590-1000 RS-232C cable 10 m (provided with the balanc

32 AD-1684: Electrostatic field meter  This option measures the amount of the static charge on the sample, tare or peripheral equipment and display

3312. TERMS/INDEX Terms Stable value The weight value when the stabilization indicator appears. Environment Ambient conditions such as vibration, d

34AX- KO3590-500 ...4, 31 AX- KO3590-1000 ...4, 31 AX-USB-9P...

35Remote controller ...31 Repeatability... 26, 28, 29, 33 RE-ZERO button ...

21. INTRODUCTION This manual describes how the AD-4212C series balance works and how to get the most out of it in terms of performance. Read this

3 Example 1 (Connecting to a personal computer or an AD-8922A) Accessory RS-232C cable (10 m)PersonalcomputerU

4 Example 2 (Connecting to a PLC) . * Specify the AD-8922A-01 connection cable when ordering the AD-8922A-01. AX-KO3705-200 2 m

51.2. Compliance Compliance with FCC Rules Please note that this equipment generates, uses and can radiate radio frequency energy. This equipment has

6Windows communicationtools (WinCT-AD4212C)AC adapterID labelRS-232C cable (10 m)Weighing panPan supportScrews (Flat head: M4 X 6)Calibration weight

7ATTACHING THE AD-4212C SERIES WEIGHING UNIT DIRECTLY ON THE MOUNTING BASE When the AD-4212C series weighing unit is built into a system, remove the