A&D HC-05 Spezifikationen

Counting Scale HC-30Ki HC-15Ki HC-6Ki HC-3Ki WM+PD4001164

82. Front Panel Overview 2. Front Panel Overview Comparator results, HI/OK/LO. TheZERO annunciato

93. BASIC OPERATIONS 3-1. Basic Operations Turn The Power ON and OFF 1. Press the ON/OFF key to turn the power ON. All the display symbols will t

10TARE  The TARE key will subtract the displayed container weight. 1. Remove everything from the weighing pan and press the ZERO key to

113-2. To Start Counting 1. Press the ON/OFF key to turn the scale ON. Or press the RESET key to initialize any previous operations. 2. Th

123-3. Unit Weight By a SAMPLE 10 Sample Size 1. The three UNIT WEIGHT BY LED’s should be blinking at this point, if not, press the RESET k

135, 25, 50 or 100 Sample Size 1. The three UNIT WEIGHT BY LED’s should be blinking at this point, if not, press the RESET key. to clear an

14Desired Sample Size 1. The three UNIT WEIGHT BY LED’s should be blinking at this point, if not, press the RESET key. to clear any unit we

15Desired Sample Size Not Using The SAMPLE Key 1. The three UNIT WEIGHT BY LED’s should be blinking at this point, if not, press the RESE

163-4. Unit Weight By KEYBOARD 1. The three UNIT WEIGHT BY LED’s should be blinking at this point, if not, press the RESET key. to clear an

173-5. Unit Weight By ID Number 1. If there are no unit weights stored into memory, see “5-1. Store unit weight by ID Numbers”. The three UNIT WEIG

This manual and Marks All safety messages are identified by the following, “WARNING” or “CAUTION”, of ANSI Z535.4 (American National Standard I

184. ENTERING A TARE WEIGHT There are two methods of tare operations.  Using the TARE key to subtract the displayed container weight directly.

194-2. To Clear TARE Either: 1. Have nothing on the weighing pan.  If the ZERO indicator is not displayed, press the ZERO key to zero the scale

205. STORE UNIT WEIGHT 5-1. Store Unit Weight by ID Numbers The scale can memorize up to 99 unit weights by 2 digit ID numbers, from 01 to 99. To rec

215-2. Clearing A Memorized Unit Weight 1. Press and hold the C key, then press the STORE UNIT WEIGHT key – release both. 2. “Clear” w

225-3. Unit Weight, Tare & Comparator Limits Memorized The scale is initially set to store ID numbers with a unit weight only. However, it can be

236. USING THE M+ MEMORY 6-1. The M+ Memory Function  The scale can accumulate count data by pressing the M+ key, or automatically (see the next

24Automatic M+ Accumulation Mode  M+ Accumulation can also be done automatically each time you count a different batch, As soon as you have a stabl

257. COMPARATOR FUNCTION  The scale contains a comparator function that checks the amount on the weighing pan against set acceptable count or weigh

26 5. Press the ENTER key to save the setting and move to next F-Function, f-05-02. 6. Continue to enter f-05 comparator settings – refer to “

278. CALIBRATION  Calibration of the scale is required when it is initially installed, if it is moved often, or it is moved a substantial distance.

1Contents 1. INTRODUCTION...

28 If you know the exact weight value, or if you wish to use a different weight, use the 0 Æ 9 and . 10-key pad to display the desire

29 8-2. Gravity Compensation When the scale is first used or has been moved to different place, it should be calibrated using a calibration weight.

30 9. F-FUNCTION PARAMETERS 9-1. To Change or View F-Function Settings  Start with the scale switched off. 1. Press and hold the ZERO key, t

319-2. F-Functions  “” designates Factory Settings. F-00-X Weight Unit  Weight Display when the scale is switched on. See also setting “f-09-0

32 ID Memory contents. The scale ID memory can contain unit weights with tare weights and comparator limits, or just unit weights alone. 003 ID memo

33F-03-X M+ Accumulation Function  M+ Accumulation – Automatic or manual 03 Manual accumulation (by pressing the M+ key). 1 Automatic accum

34010  Auto power-off 03 Auto power-off disabled. 1 Auto power-off enabled.  “f-04-06” is for factory use and should be “0”. F-05-X Comparato

35F-06-X RS-232C Data Output F-06-X requires OP-03 or OP-04 RS-232C interface.  Data Out Mode 03 Key Mode: Data is sent by pressing the PRINT

36 Data Length and Parity 03 7 bits, even parity. 1 7 bits, odd parity. 2 8 bits, non parity.  “f-07” and “f-08” are for factory use and should b

3710. ACAI FUNCTION 10-1. ACAI Automatic Counting Accuracy Improvement The ACAITM (Automatic Counting Accuracy Improvement) function recalculates

211. AWA FUNCTION...39 11

38 Pcs On the ACAI Weighing Pan Addition Range 60 63~122 10 13~26 70 73~138 20 23~49 80 83~152 30 33~70 90 93~166 40 43~89 100 103~299 50 53~

39 11. AWA FUNCTION 11-1. AWA Audible Weighing Assist The AWA (Audible Weighing Assist) function will assist you to count a certain amount of pi

40Tasrget Mode Setting 1. The count display shows target count blinking. 2. Use the 0 Æ 9 keys to set or change the count. The C

4112. OP-02 BATTERY Using OP-02 SLA Battery  The scale can operate with by an SLA (Sealed Lead Acid) battery that will be commercially available. 

42Charging the Battery WWhen the count display shows “lo bat”, the battery power is almost exhausted and should be recharged. While the scale is op

4313. OP-03 RS-232C SERIAL INTERFACE This interface allows the HC-i series to be connected with a multifunction printer or a personal computer.  The

44 The HC-i is designated as DCE (Data Communication Equipment). 13-3. Data Output Mode  The Data Output Modes and Parameters are set by F-Function

45 Baud Rate (f-06-04) Select the baud rate according to the device to be connected.  2400 bps (f-06-04="0") Select 2400 bps to connect wi

46 13-5. Connecting the AD-8121 Printer / MODE 3  When using MODE 3 of the AD-8121 printer, printouts are obtained using the PRINT key (f-06-01

47 Command List Command Definition Notes @ Start / stop continuous data transmission. A Same as RESET key. Key command D Set a known tare

31. INTRODUCTION 1-1. Introduction Thank you for your Purchase! This manual describes the functions of your counting scale and how to get the most o

48 If the command is S , T or Z , the scale will send a second acknowledgment <ACK><CR><LF> or <ACK> (see F-Funct

49  Unit Weight Command ? U W CLF Reply U W, + 1 . 234567[ [ gCLF U W, + 0 . 272531[ lbCLF  Total Count Command ? A Q CLF Reply A Q, + 0 0

50Reply ACKCLF ID Number: Maximum 6 digit Upper Limit: Maximum 9 digit including sign Lower Limit: Maximum 9 digit including sign  Re

5113-6. Using UFC (Universal Flex Coms) Function  The UFC function allows you to print out as you format the printer (UFC format).  The scale can s

52PF,‘ID~’,$CD,$CR,$LF,& $CR,$LF,& ‘Count’,$CR,$LF,& $SP4,$PC,$CR,$LF,& ‘Unit~Weight’,$CR,$LF,& $SP4,$UW,$CR,$LF,& ‘Weight’,$

5314. OP-04 RS-232C & RELAY OUTPUT RS-232C interface and relay output for comparator results are obtained by installing OP-04.  The OP-04 unit i

5415. SPECIFICATIONS MODEL HC-3Ki HC-6Ki HC-15Ki HC-30Ki Capacity kg 3 kg 6 kg 15 kg 30 kg Resolution (k)g 0.0005 kg 0.001 kg 0.002 kg 0.005

5516. GRAVITY ACCELERATION MAP Values of gravity at various locations Amsterdam 9.813 m/s2 Manila 9.784 m/s2 Athens 9.807 m/s2 Melbourne 9.80

56World map

(blank page)

41-2. Unpacking  Unpack the scale carefully and keep the packing material if you are likely to transport the scale again in the future.  In the car

51-4. Setting Up Your Scale 1. Place the scale on a suitable weighing surface (see “Best Conditions For Weighing” below) and turn the adjustable feet

61-5. Simple Operation Mode If desired, the HC-i scale can be set in a Simple Operation Mode. Set the F-Function f-01-01 at “1”. In this mode, only f

73. Press the ENTER key. The scale will recall the previous unit weight. This feature cannot be used in Simple Operation Mode. Automatic